The 2020 Code Making Panel (CMP) has revised the 2017 NEC rules regarding receptacles serving dwelling unit balconies, decks, and porches – specifically, the requirement that an accessible outdoor receptacle must be installed to serve attached balconies, decks, and porches. The revised Code now requires that a receptacle be installed to serve the balcony, deck, or porch when the balcony, deck, or porch is within 4 inches of the dwelling unit. If the balcony, deck, or porch is within 4 inches of the dwelling, the 2020 NEC considers that close enough so that it now requires a general use 120-volt receptacle.
If you ask a seasoned electrician how many No. 12 AWG conductors will fit into a 3/4″ EMT conduit system, you may get a response such as “one more!” While this is amusing (and typically true), there are precautions that must be taken according to the NEC whenever conductors are bundled together in a raceway, cable, or even in a ditch in the earth.
In this 2020 Code cycle a new Informational Note now accompanies the term Grounded Conductor where it is defined in Article 100. The Note has been added to help electricians identify functional differences between Grounded and Grounding Conductors.
In defense of all who have struggled with these terms in the past, both grounded conductors and grounding conductors are in fact grounded. They just have different jobs.
Every electrician must have a good electrical resume on hand and be ready to share it when the next opportunity presents itself. Your resume must be able to stand out against many others in the usual quick review. As an electrician and as an employer, I can tell you the following layout is very informative and very successful.
Section 408.6: A Brand-New Addition to the 2020 NEC
NEC section 408.6 states: Switchboards, Switchgear, and Panelboards shall have a short-circuit current rating (SCCR) not less than the available fault current. In other than one- and two-family dwelling units, the available fault current and the date the calculation was performed shall be field marked on the enclosure at the point of supply. The marking shall comply with 110.21(B)(3).
Making NEC 408.6 Simple
This new Code Section simply means that electrical panels including main-breaker and main-lug type panels and switchboards & switchgear equipment must be rated (in amps) to withstand the high levels of current that will flow should a short-to-ground or other fault occur at the equipment. In ALL locations other than dwelling units, that anticipated fault current must be marked on the equipment enclosure near where the supply conductors enter in, along with the date that the calculation producing that number was performed. The new Code Section also says the markings on the equipment must comply with 110.21(B)(3). Section 110.21(B)(3) tells us that markings must be sufficiently durable to withstand the environment.
The 2020 NEC now recognizes that GFCI protection for mobile and manufactured homes must be equal to that of stick-built and modular type dwellings. Construction Codes, in general, have always been less restrictive for mobile-type dwellings. This may be because mobile homes are often titled with the Motor Vehicle Department, and this type of housing is built, inspected, tested, and listed off-site at a manufacturing plant.
Licenses for Registered and Certified Electricians will expire on August 31st of every even numbered year. You will need to renew your license before expiration to avoid additional fees or your license becoming null and void. If your license becomes null and void, you will have to reapply as if you have never held a Florida electrical license.
Montana electrical licenses will expire on July 15, 2020. To continue working under your Montana electrical license you must complete and application and continuing education courses. Renewal opens 60 days prior to the expiration date.
Transformers are used when power voltages need to be changed, or transformed, to other levels. Sometimes voltages need to be increased when sending power long distances. Other times, voltages need to be decreased for equipment that uses the power. Regardless of whether the voltages are being stepped up or stepped down, the same process of changing windings is used to transform voltages to different levels.
Don't wait for an Electrical Inspector to teach you the 2023 NEC. Save time, money, and pass inspections the first time by completing our online continuing education courses.